| 查看上一个主题 :: 查看下一个主题 |
| 作者 |
内容 |
themoleman342
 注册时间: 2007年10月21日 文章: 2190 来自: East Coast (CT), U.S.A.
Expire: 2013-01-24
|
 发表于: 周六 6月 27, 2009 12:33 am 文章标题: Newton Rings |
|
 发表于: 周六 6月 27, 2009 12:33 am 文章标题: Newton Rings |
|
|
themoleman342 wrote:
I've read a bit about Newton Rings in the past few hours. I was having trouble with a set of black and white negatives. Not real black and white but rather Kodak's C-41 processing "B&W" film. I generally hate this film but shot it once in a while just for quick developing, or at least I did before I had my darkroom set up.
I thought the problem was pressure of the lid was not sufficient to hold the negative flat and the gap that resulted was causing them. But even with excess pressure the problem did not improve in the slightest. Someone had defined the issue as having to do with "two shiny surfaces coming into contact with each other." With most film there is a dull (emulsion) and shiny side. The canoscan recommends that the emulsion side be down. Now I understand why.
With Kodak's "B&W" film there is no discernible difference between the sides. Both are considerably "shiny." So essentially this film, no matter which way you face it, creates the "two shiny surfaces" issue.
This is probably old hat to many of you. But I figured I'd offer this advice: stay away from this film if you are scanning on a flatbed type setup or don't have an anti-newton ring apparatus. I know I'll never buy the film again.
~Marc |
|
| 返回顶部 |
|
 |
Katastrofo
 注册时间: 2007年2月26日 文章: 10405 来自: USA
Expire: 2013-11-19
|
 发表于: 周六 6月 27, 2009 2:31 am 文章标题: |
|
 发表于: 周六 6月 27, 2009 2:31 am 文章标题: |
|
|
Katastrofo wrote:
The best way to tell is by reading what's in the borders of the film. If you
can make out the word 'Kodak' that's the shiny, or shinier side that should
be up. |
|
| 返回顶部 |
|
 |
Seele
 注册时间: 2009年4月17日 文章: 746 来自: Sydney Australia
|
 发表于: 周六 6月 27, 2009 8:20 am 文章标题: |
|
 发表于: 周六 6月 27, 2009 8:20 am 文章标题: |
|
|
Seele wrote:
The great photographer and technical man Andreas Feininger recommended the use of glassless carriers for 35mm negatives, as the negative base has enough stiffness to stay flat, if properly supported in a well-designed carrier. For larger formats, such as 4"X5" I use a custom carrier with glass only on top and that never created any problems for me.
But if you are stuck with just the glass carrier with glass both on top and below the negative, you can treat the glass surfaces to prevent Newton's Rings:
Find a small atomiser bottle; I use the ones which used to contain spectacle cleaning fluid, but you can see what you can get. Mix up a dilute solution of gum arabic using distilled water to ensure no particles in it and put it in the bottle. A concentrated gum arabic solution should be available from an art supply dealer, it is used as a binder for watercolour.
Take the glass pieces out of the carrier, clean them properly and let dry. Then place them on a flat support, say a sheet of clean paper, but do not lift them up from the paper surface, otherwise the coating would not be even.
From a reasonable distance, say half metre, lightly spray the solution in the air and let it coat the glass surfaces. Do not go overboard as if doing spray painting, a light coating is good. When dry, examine it under bright daylight, if you see a coloured mottling reflection, like a film of oil floating on water, then it is done. Replace glass carefully, then try again.
When the coating is worn out or rubbed, you can wash it off and repeat the process. |
|
| 返回顶部 |
|
 |
Orio
注册时间: 2007年2月24日 文章: 29545 来自: West Emilia
Expire: 2012-12-04
|
 发表于: 周六 6月 27, 2009 8:59 am 文章标题: |
|
 发表于: 周六 6月 27, 2009 8:59 am 文章标题: |
|
|
Orio wrote:
hi Marc,
the Canoscan advice tells it all - and it's not only valid for Canon scanner, it's a universally good advice. I do get Newton rings and also Moiré if I scan the strips with the emulsion side up. I did that for mistake in my scans of the BW film strips I posted yesterday - and if you look closely, you will see obvious Moiré in some of the images.
Luckily, the remedy is simple : just scan with the emulsion side down.  _________________ Orio, Administrator
T*
NE CEDE MALIS AUDENTIOR ITO
Ferrania film is reborn! http://www.filmferrania.it/
Support the Ornano film chemicals company and help them survive!
http://forum.mflenses.com/ornano-chemical-products-t55525.html |
|
| 返回顶部 |
|
 |
Xpres
 注册时间: 2007年12月11日 文章: 964 来自: UK
Expire: 2014-10-28
|
 发表于: 周六 6月 27, 2009 10:04 am 文章标题: |
|
 发表于: 周六 6月 27, 2009 10:04 am 文章标题: |
|
|
Xpres wrote:
You can buy anti newton ring glass. I have pieces for my enlargers in different formats for when the negs need some support - quite often with 6x9 as you're not going to get critical sharpness with a curved neg in a glassless carrier.
I haven't tried it in a scanner yet, but a sandwich of glass under and ang over placed on the scan bed should do the trick - as longs as the lower glass is the right thickness so the head can focus.
I did put a piece of ground glass on some curly negs the other day which worked for sharpness but contained too much of the ground glass! I just turned the negs around against the curl which was OK for a web scan. _________________ Film... and sometimes SD14, 5D2 and some other suff! |
|
| 返回顶部 |
|
 |
Farside
 注册时间: 2007年9月1日 文章: 6579 来自: Ireland
Expire: 2013-12-27
|
 发表于: 周六 6月 27, 2009 4:53 pm 文章标题: |
|
 发表于: 周六 6月 27, 2009 4:53 pm 文章标题: |
|
|
Farside wrote:
@ Seele.
Interesting gum arabic idea. Must bear that in mind. _________________ Dave - Moderator
Camera Fiend and Biograph Operator
If I wanted soot and whitewash I'd be a chimney sweep and house painter.
The Lenses of Farside (click)
BUY FRESH FOMAPAN TO HELP KEEP THE FACTORY ALIVE ---
Foma Campaign topic -
http://forum.mflenses.com/foma-campaign-t55443.html
FOMAPAN on forum -
http://www.mflenses.com/fs.php?sw=Fomapan
Webshop Norway
http://www.fomafoto.com/
Webshop Czech
https://fomaobchod.cz/inshop/scripts/shop.aspx?action=DoChangeLanguage&LangID=4 |
|
| 返回顶部 |
|
 |
|
|
|
您不能在本版块发表新主题 您不能回复本版块的主题 您不能编辑自己在版块内的文章 您不能删除自己在版块内的文章 您不能参与本版块的投票
|