| 查看上一个主题 :: 查看下一个主题 |
| 作者 |
内容 |
Katastrofo
 注册时间: 2007年2月26日 文章: 10405 来自: USA
Expire: 2013-11-19
|
 发表于: 周五 11月 13, 2009 1:35 pm 文章标题: Agfa Neutol? |
|
 发表于: 周五 11月 13, 2009 1:35 pm 文章标题: Agfa Neutol? |
|
|
Katastrofo wrote:
Has anyone used the above and do you have samples? Found an
example off of flickr:
http://farm3.static.flickr.com/2114/2358543794_21edf9d06f_o.jpg
Hummm. |
|
| 返回顶部 |
|
 |
Sevo
 注册时间: 2008年8月22日 文章: 1189 来自: Frankfurt, Germany
Expire: 2012-12-03
|
 发表于: 周五 11月 13, 2009 2:56 pm 文章标题: |
|
 发表于: 周五 11月 13, 2009 2:56 pm 文章标题: |
|
|
Sevo wrote:
That is (or was) the standard Agfa paper developer, and does not differ much from those from Ilford or Kodak. I suppose the print was developed in it rather than the film. _________________ Sevo |
|
| 返回顶部 |
|
 |
Katastrofo
 注册时间: 2007年2月26日 文章: 10405 来自: USA
Expire: 2013-11-19
|
 发表于: 周五 11月 13, 2009 3:02 pm 文章标题: |
|
 发表于: 周五 11月 13, 2009 3:02 pm 文章标题: |
|
|
Katastrofo wrote:
Sevo, thanks. It looks good if I ever start printing. |
|
| 返回顶部 |
|
 |
Seele
 注册时间: 2009年4月17日 文章: 746 来自: Sydney Australia
|
 发表于: 周五 11月 13, 2009 4:08 pm 文章标题: |
|
 发表于: 周五 11月 13, 2009 4:08 pm 文章标题: |
|
|
Seele wrote:
I used Neutal NE quite a lot and it's a standard print developer, Neutal WA gave warm tones when matched with suitable papers; I certainly miss Portriga!
Since you compound your solutions from raw chemicals, when you are to do printing, there would be no shortage of formulae for paper developers to try out. From a comparative test I conducted a few years ago, I found that Focal Universal is a good one for allround work at low cost, but MCM Winchester (original formula) gives outstanding results, perhaps even slightly better than Neutol. |
|
| 返回顶部 |
|
 |
Katastrofo
 注册时间: 2007年2月26日 文章: 10405 来自: USA
Expire: 2013-11-19
|
 发表于: 周六 11月 14, 2009 1:48 am 文章标题: |
|
 发表于: 周六 11月 14, 2009 1:48 am 文章标题: |
|
|
Katastrofo wrote:
Seele, thanks for the heads-up on the formulas. I'm a ways from doing
printing, but mixing raw chems is almost 2nd nature after my navy
experience. |
|
| 返回顶部 |
|
 |
Seele
 注册时间: 2009年4月17日 文章: 746 来自: Sydney Australia
|
 发表于: 周六 11月 14, 2009 5:38 am 文章标题: |
|
 发表于: 周六 11月 14, 2009 5:38 am 文章标题: |
|
|
Seele wrote:
In case you cannot find the recipes for the two paper developers I mentioned, here they are:
MCM Winchester
Metol 4.25g
Sodium sulphite (anhydrous) 50g
Hydroquinone 12.5g
Sodium carbonate (anhydrous) 100g
Potassium bromide 6.25g
Water to 1 litre
To use, dilute 1:3.
If you use sodium carbonate in monohydrate form, use 118.5g instead.
Personal notes taken after comparison test:
"This gives very brilliant, clean-looking prints on baryta papers. Light to mid greys appear to have extra separation, whites stay very bright, but highlight details, if too weak, can be brought out by methods like prior treatment in Ansco 120. Compared to standard developers such as Ilford MG, the blacks seem to have an extra depth which goes right into the paper."
____
Focal Universal
Metol 1g
Sodium sulphite (anhydrous) 25g
Hydroquinone 3.7g
Sodium carbonate (anhydrous) 25g
Potassium bromide 0.3g
Water to 1 litre
To use, dilute 1:1
If you use sodium carbonate in monohydrate form, use 30g instead.
Personal notes taken after comparison test:
"This behaves in a similar way as Ilford MG, but without the slight compression of mid greys. Development times should be a little longer, say an extra 50%."
Hope this is of interest. |
|
| 返回顶部 |
|
 |
Katastrofo
 注册时间: 2007年2月26日 文章: 10405 来自: USA
Expire: 2013-11-19
|
 发表于: 周六 11月 14, 2009 2:46 pm 文章标题: |
|
 发表于: 周六 11月 14, 2009 2:46 pm 文章标题: |
|
|
Katastrofo wrote:
Seele, thanks much for this! I'm going to bookmark this thread.
Actually, will see about printing this out, too. |
|
| 返回顶部 |
|
 |
|
|
|
您不能在本版块发表新主题 您不能回复本版块的主题 您不能编辑自己在版块内的文章 您不能删除自己在版块内的文章 您不能参与本版块的投票
|