MFlenses - 数码时代的新生
MFLenses 2026

手动对焦镜头论坛

通过维修记录、实拍样片和图文丰富的档案帖,探索老镜头的世界。

通过维修记录、实拍样片和图文丰富的档案帖,探索老镜头的世界。
精选

论坛首页的合作伙伴展示位。

Question about flash voltage
查看上一个主题 :: 查看下一个主题  


Reply

Hello Smile

I curently own an old flashgun Sunpack 134 (european name of Sunpack411), and since I read some things on the web about the dangerousity for the camera to use flash with high voltage, I was wondering if I could use it safely on my 40D.

My research lead me to think that I can use it on the PC port (not on the hotshoe), because I read on user guide that 40D can be used with flash that has voltage not higher than 250v. This flash is supposed to deliver 190v (source http://dpanswers.com/roztr/volt_finder.php ).

So, Am I right? Can I use it on PC port?

Also, are there any kind of Hot shoe adapter that I could use (that make me able to mount and use the flash on my 40D hot shoe)? I already saw stuff like that but I'm not sure it is what I need...

Simply, I have very few knowledge about flash and voltage things (I want to use flash in order to learn how to use them right)... and I don't wanna destroy my lovely camera just because I didn't know even the basic things.


Reguards,

Pierre


Reply

BurstMox 写道:
Hello Smile

I curently own an old flashgun Sunpack 134 (european name of Sunpack411), and since I read some things on the web about the dangerousity for the camera to use flash with high voltage, I was wondering if I could use it safely on my 40D.

My research lead me to think that I can use it on the PC port (not on the hotshoe), because I read on user guide that 40D can be used with flash that has voltage not higher than 250v. This flash is supposed to deliver 190v (source http://dpanswers.com/roztr/volt_finder.php ).

So, Am I right? Can I use it on PC port?

Also, are there any kind of Hot shoe adapter that I could use (that make me able to mount and use the flash on my 40D hot shoe)? I already saw stuff like that but I'm not sure it is what I need...

Simply, I have very few knowledge about flash and voltage things (I want to use flash in order to learn how to use them right)... and I don't wanna destroy my lovely camera just because I didn't know even the basic things.


Reguards,

Pierre


The strobe Volt page tells your Sunpak 134 is only 43.5 Volts, too much for the hotshoe but good for the PC sync connector. Did you measure it?. It's easy: switch it on and when the "ready" light is lit, measure with a VOM the CC voltage across the two main contacts (lateral and center tip).

You can use it safely, but NEVER on the hotshoe directly.
If it's mandatory to use it on the hotshoe, you will have to buy a hotshoe isolator (a small thing that fits on the hotshoe and adds some protective electronics that can handle the high voltage without trouble.
The one that you point out seems not to be an isolator, just an adapter.

This one may fit the bill: 点击此处在 eBay 上查看

Good luck, please tell us your experience once tested.
Regards.
Jes.


Reply

That's strange about 134's voltage. Well, mine is "Auto134", maybe that's the difference. This guy here tells "The SUNPAK 411 is also known as SUNPAK 134 wich is the european version."

Well, I guess that's not big deal, since none of them are above 250v Smile .

I need to try now.

Thx for answer


Reply

I think the hotshoe and PC are on the same circuit? I know I went into triple figures with my flash voltage a number of times on my 40D.

The word on the street is that the later Canons EOS (post 350d) were fine with up to 250v.


Reply

I tested the flash, it's well synchronized. After 1 shot, my 40D is still alive.