| 查看上一个主题 :: 查看下一个主题 |
| 作者 |
内容 |
55
 注册时间: 2013年5月13日 文章: 773 来自: U.S.
Expire: 2026-07-24
|
 发表于: 周三 10月 06, 2021 12:48 am 文章标题: Any tips for reassembling focus helicoids? |
|
 发表于: 周三 10月 06, 2021 12:48 am 文章标题: Any tips for reassembling focus helicoids? |
|
|
55 wrote:
My Sun 80-240mm f/4's focus assembly needed new grease. I was able to separate the focus helicoid and clean the two halves with no trouble. But now I simply cannot get the two to mate again.
I marked the point at which the upper and lower pieces separated so that's not an issue. And I've disassembled many helicoids before and have almost always been able to successfully get them back together.
However, most of the lenses I've worked on have been primes with fine threaded helicoids. The Sun is different because it has wider threads, and that may be why I'm having difficulty.
As far as I can see, the threads are in good condition and the barrels aren't bent.
When reassembling, I generally rotate one half in the "wrong" direction in order to find the starting point where the two halves should join. In the past, gentle persistence has usually been enough to rejoin a helicoid. Occasionally, I've resorted to applying light pressure to help get the pieces started back together.
For the Sun, I've heated the female half in an attempt to make the opening a bit larger. And I've tried to mate the halves first without grease on the threads, and then with. No success.
Determining if the halves are aligned properly while attempting to rejoin them is difficult. Member visualopsins suggested: "Tip -- place half on flat surface rather than trying to screw together holding both pieces." in this thread:
http://forum.mflenses.com/viewtopic.php?t=82793
But that hasn't worked for me, either. The two halves just won't bite / engage.
Any suggestions?
my lens:
 |
|
| 返回顶部 |
|
 |
visualopsins
 注册时间: 2009年3月5日 文章: 11700 来自: California
Expire: 2027-07-11
|
 发表于: 周五 1月 21, 2022 2:46 am 文章标题: |
|
 发表于: 周五 1月 21, 2022 2:46 am 文章标题: |
|
|
visualopsins wrote:
place one half on sturdy flat surface
approach with other half at a tilt and hook other half onto lower half threads, then tilt into position, screw helicals together.
(or something like that )
An anecdote: I had a similar problem solved after a good night's sleep on retry -- I had been turning the helicals in the wrong direction. _________________ ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮ like attracts like! ☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮☮
Cameras: Sony ILCE-7RM2, Spotmatics II, F, and ESII, Nikon P4
Lenses:
M42 Asahi Optical Co., Takumar 1:4 f=35mm, 1:2 f=58mm (Sonnar), 1:2.4 f=58mm (Heliar), 1:2.2 f=55mm (Gaussian), 1:2.8 f=105mm (Model I), 1:2.8/105 (Model II), 1:5.6/200, Tele-Takumar 1:5.6/200, 1:6.3/300, Macro-Takumar 1:4/50, Auto-Takumar 1:2.3 f=35, 1:1.8 f=55mm, 1:2.2 f=55mm, Super-TAKUMAR 1:3.5/28 (fat), 1:2/35 (Fat), 1:1.4/50 (8-element), Super-Multi-Coated Fisheye-TAKUMAR 1:4/17, Super-Multi-Coated TAKUMAR 1:4.5/20, 1:3.5/24, 1:3.5/28, 1:2/35, 1:3.5/35, 1:1.8/85, 1:1.9/85 1:2.8/105, 1:3.5/135, 1:2.5/135 (II), 1:4/150, 1:4/200, 1:4/300, 1:4.5/500, Super-Multi-Coated Macro-TAKUMAR 1:4/50, 1:4/100, Super-Multi-Coated Bellows-TAKUMAR 1:4/100, SMC TAKUMAR 1:1.4/50, 1:1.8/55
M42 Carl Zeiss Jena Flektogon 2.4/35
Contax Carl Zeiss Vario-Sonnar T* 28-70mm F3.5-4.5
Pentax K-mount SMC PENTAX-A ZOOM 1:3.5 35~105mm, SMC PENTAX ZOOM 1:4 45~125mm
Nikon Micro-NIKKOR-P-C Auto 1:3.5 f=55mm, NIKKOR-P Auto 105mm f/2.5 Pre-AI (Sonnar), Micro-NIKKOR 105mm 1:4 AI, NIKKOR AI-S 35-135mm f/3,5-4,5
Solinon 1:5.6/18 ASPH.
Tamron SP 17mm f/3.5 (51B), Tamron SP 17mm f/3.5 (151B), SP 500mm f/8 (55BB), SP 70-210mm f/3.5 (19AH)
Vivitar 100mm 1:2.8 MC 1:1 Macro Telephoto (Kiron)
|
|
| 返回顶部 |
|
 |
RokkorDoctor
 注册时间: 2021年11月27日 文章: 1562 来自: Kent, UK
Expire: 2025-05-01
|
 发表于: 周五 1月 21, 2022 2:29 pm 文章标题: |
|
 发表于: 周五 1月 21, 2022 2:29 pm 文章标题: |
|
|
RokkorDoctor wrote:
Multi-thread helicoids can be a bit a bit difficult sometimes.
I have found indeed that placing one half down and lowering the other works much better, trying to mate them whilst holding both in your hands will be nigh impossible. What may help alignment is first make sure the table is level, place the bottom helicoid half on the table, and lay a bubble level on top of the top helicoid half (e.g. on a stiff flat plate/card across the opening).
Pressure/force should really be avoided, it won't do any good; you will simply damage the thread ends. Instead, this is all about meticulous and careful alignment.
In the end, for problematic ones I have found simply patience to be the only solution.
I often leave the very ends of the threads un-lubricated, and with good alignment and very sensitive rotation in the wrong direction, you can often feel a faint "click" when all the threads engage; then immediately rotate the threads together. Note this "click" is much more subtle and faint as compared to a single start thread!!
Be careful with that helicoid you have there; that's an alu-alu combo which you really shouldn't try to screw together too far without any lubrication. Aluminium on aluminium galls easily when dry, which will damage the threads and you might not even be able to get them apart again.
Again, patience, and Good Luck!  _________________ Mark
SONY A7S, A7RII + dust-sealed modded Novoflex/Fotodiox/Rayqual MD-NEX adapters
Minolta SR-1, SRT-101/303, XD7/XD11, XGM, X700
Bronica SQAi
Ricoh GX100
Minolta majority of all Rokkor SR/AR/MC/MD models made
Sigma 14mm/3.5 for SR mount
Tamron SP 60B 300mm/2.8 (Adaptall)
Samyang T-S 24mm/3.5 (Nikon mount, DIY converted to SR mount)
Schneider-Kreuznach PC-Super-Angulon 28mm/2.8 (SR mount)
Bronica PS 35/40/50/65/80/110/135/150/180/200/250mm |
|
| 返回顶部 |
|
 |
cooltouch
 注册时间: 2009年1月15日 文章: 9096 来自: Houston, Texas
|
 发表于: 周五 1月 21, 2022 9:17 pm 文章标题: |
|
 发表于: 周五 1月 21, 2022 9:17 pm 文章标题: |
|
|
cooltouch wrote:
I've disassembled a number of lenses and inevitably I'm confronted with this problem. There's no easy way I've found. Persistence definitely helps. One thing I do that I think helps is I'll turn the top piece ion the opposite direction from the threads (ie, if right thread, then turn the piece to the left), and while doing this, I listen and feel for a slight click that lets me know the threads have dropped into place. Then I'll turn the top piece in the correct direction and, with a bit of luck, I'll have engagement. And then I hope I've engaged the right threads, or else I get to do it all over again. I usually check to see if the right threads have engaged by checking focusing and focusing marks at infinity. _________________ Michael
My Gear List: http://michaelmcbroom.com/photo/gear.html
My Gallery: http://michaelmcbroom.com/gallery3/index.php/
My Flickr Page: https://www.flickr.com/photos/11308754@N08/albums
My Music: https://soundcloud.com/michaelmcbroom/albums
My Blog: http://michaelmcbroom.com/blogistan/ |
|
| 返回顶部 |
|
 |
55
 注册时间: 2013年5月13日 文章: 773 来自: U.S.
Expire: 2026-07-24
|
 发表于: 周二 4月 12, 2022 5:01 pm 文章标题: Belated Bump! |
|
 发表于: 周二 4月 12, 2022 5:01 pm 文章标题: Belated Bump! |
|
|
55 wrote:
Your advice is appreciated and I apologize for my delayed response! Somehow I lost track of this topic.
Ah, these stubborn lenses really are a test of patience! But I'm glad to know I'm not the only one who has endured such bliss.
If I ever succeed, I'll let you know.
Eventually. |
|
| 返回顶部 |
|
 |
jackwilson
注册时间: 2022年9月26日 文章: 1
|
 发表于: 周一 9月 26, 2022 1:41 pm 文章标题: Re: Any tips for reassembling focus helicoids? |
|
 发表于: 周一 9月 26, 2022 1:41 pm 文章标题: Re: Any tips for reassembling focus helicoids? |
|
|
jackwilson wrote:
| 55 写道: |
My Sun 80-240mm f/4's focus assembly needed new grease. I was able to separate the focus helicoid and clean the two halves with no trouble. But now I simply cannot get the two to mate again.
I marked the point at which the upper and lower pieces separated so that's not an issue. And I've disassembled many helicoids before and have almost always been able to successfully get them back together.
However, most of the lenses I've worked on have been primes with fine threaded helicoids. The Sun is different because it has wider threads, and that may be why I'm having difficulty.
As far as I can see, the threads are in good condition and the barrels aren't bent.
When reassembling, I generally rotate one half in the "wrong" direction in order to find the starting point where the two halves should join. In the past, gentle persistence has usually been enough to rejoin a fm whatsapp apk helicoid. Occasionally, I've resorted to applying light pressure to help get the pieces started back together.
For the Sun, I've heated the female half in an attempt to make the opening a bit larger. And I've tried to mate the halves first without grease on the threads, and then with. No success.
Determining if the halves are aligned properly while attempting to rejoin them is difficult. Member visualopsins suggested: "Tip -- place half on flat surface rather than trying to screw together holding both pieces." in this thread:
But that hasn't worked for me, either. The two halves just won't bite / engage.
Any suggestions?
my lens:
 |
Hi there I am newbie here and I have a small question about starting my carrier in Photography,
I want to know which is the best Camera for me as beginner. |
|
| 返回顶部 |
|
 |
55
 注册时间: 2013年5月13日 文章: 773 来自: U.S.
Expire: 2026-07-24
|
 发表于: 周三 9月 28, 2022 3:55 am 文章标题: Re: Any tips for reassembling focus helicoids? |
|
 发表于: 周三 9月 28, 2022 3:55 am 文章标题: Re: Any tips for reassembling focus helicoids? |
|
|
55 wrote:
| jackwilson 写道: |
Hi there I am newbie here and I have a small question about starting my carrier in Photography,
I want to know which is the best Camera for me as beginner. |
Welcome, jackwilson.
Your small question has a large number of possible answers!
You'd probably get a more informed reply than I can give if you start a new topic to ask your question.
I'd suggest you try in the Photographer's Cafe:
http://forum.mflenses.com/the-photographers-cafe-f9.html
If you choose to post in the Cafe, please include details about your level of photographic experience, shooting interests and budget. |
|
| 返回顶部 |
|
 |
|
|
|
您不能在本版块发表新主题 您不能回复本版块的主题 您不能编辑自己在版块内的文章 您不能删除自己在版块内的文章 您不能参与本版块的投票
|